Skip to main content
VRS Black FridaySee all deals →
VRS Logo
VRS Logo
Pro G2 Pedals
VRS® DirectForce® Pro G2

G2 Clutch (Sport)

Pure mechanical precision.

Coming soon

Not yet available to order in your country. Dates follow soon.

Measure the driver. Not the pedal. A brake that firms up like a race car's, a zero-friction throttle and a clutch that lets go like the real thing, with a load cell on every pedal.

Key features

  • ProgressiveMechanical brake, no hydraulics
  • Zero frictionThrottle on a ball bearing
  • Real clutch feelForce drops at the end of the stroke
  • Load cellOn every pedal, part of the frame
  • Steel springsSame force hot or cold
  • Adjust on the rigPreload, brake curve, face height and tilt
  • CNC-machined facesAluminium, sandblasted, black anodised
  • European UnionMade in
  • 3 yearsLimited warranty
G2 Clutch (Sport)
G2 Clutch (Sport)
G2 Clutch (Sport)
G2 Clutch (Sport)
G2 Clutch (Sport)
G2 Clutch (Sport)
G2 Clutch (Sport)
Pure mechanical precision

Measure the driver. Not the pedal.

G2 brake bell crank and tie rod
Brake

A brake that feels the same on every lap

200 kgload cell that carries the pedal arm

A tie rod and bell crank make the force rise faster the further you press, so the pedal firms up under your foot the way a race car brake does. No oil, no seals, nothing to bleed.

  • Progressive tie rod and bell crank linkage
  • Crank CNC-machined from solid 6061 aluminium
  • Adjustable curve, with measured force graphs
G2 brake springs
Springs

Steel springs: the same force, hot or cold

2 springsin the box, the red one roughly doubles the force

Elastomers push back differently on release than on press, and soften as they warm. A steel spring gives the same force at the same travel, in the first ten minutes and the last.

  • Steel compression springs, no elastomers
  • Blue fitted, red included
G2 throttle spring on its centre shaft
Throttle

A zero-friction throttle

10 kgload cell in the pedal arm

The back of the spring sits in a swing bracket that turns on a ball bearing, so the spring and its shaft pivot with the pedal and the spring is always pressed in a straight line, never bent or binding, even with a lot of preload. No notch at the start of the travel: the pedal moves the instant you touch it and follows when you lift.

  • Ball-bearing swing bracket
  • Polished 304 stainless shaft in a low-friction POM bearing
  • Tool-free preload knob
G2 clutch linkage
Clutch

A clutch that feels like a real car’s

80 kgload cell

The force rises, then falls away at the end of the stroke, as it does with a diaphragm spring. Your foot finds the same reference point for every start and downshift.

  • Geometry modelled on a diaphragm-spring clutch
  • Rear pivot held on both sides, on ball bearings
G2 hydraulic damper
Damper · fitted on Elite

A hydraulic damper for a steadier pedal

Adjustabledamping, held by a locking screw

The damper resists more the faster you press, so trail braking becomes a controlled release. Elite has one on every pedal. On Sport every arm is prepared for the G2 Damper Upgrade Kit.

  • Runs on bearings: adds damping, not friction
  • Fits the throttle, brake or clutch
Engineering details

Rigid build, tool-free adjustment, clean signal

  • G2 load cell

    The load cell is part of the frame

    On every G2 pedal the load cell is a load-bearing part. Fewer parts between foot and sensor means less to flex and nothing to drift out of line.

    Load cells: 200 kg brake · 80 kg clutch · 10 kg throttle

  • G2 preload knob

    Tool-free preload on every pedal

    Spring preload on all three pedals is set by a machined aluminium knob, by hand, with the pedals bolted down.

    CNC aluminium preload knobs, carbon grey anodised

  • G2 pedal face mount

    Pedal faces adjust for height and tilt

    The face sits on a two-screw mount. Slide it along the 27 mm slots to set its height, and set its tilt so it meets your sole flat.

    Two-screw face mount · 27 mm height range · adjustable tilt

  • G2 pedal feet

    3 mm steel plate, built not to flex

    A 3 mm steel frame on thick steel feet holds the pedal still under your hardest stop. Tilt locks into fixed holes, so left and right always match.

    5 fixed tilt positions, about 20° · dual end stops, 70 and 90 Shore

  • G2 Elite machined pedal faces

    CNC-machined aluminium faces on both editions

    Sport faces are 2 mm aluminium with CNC-machined edges, sandblasted and black anodised. Elite faces are machined from solid 6061, carbon grey anodised, fixed from the sides with a diamond grip on the brake and clutch.

    Both curved to R400 · Elite faces available for Sport as G2 Face Upgrade Kits

  • VRS Pedal controller

    A 24-bit controller for a clean signal

    All three load cells are read by a low-noise amplifier and a 24-bit converter. VRS One handles calibration, maximum brake force and dead zones.

    VRS Pedal controller · 24-bit ADC · USB

G2 Pedals Specs, Box Contents & Editions

Brake

  • 200 kg load cell that carries the pedal arm
  • Progressive tie rod and bell crank linkage, no oil or seals
  • One-piece CNC-machined 6061 aluminium crank
  • Steel springs, no elastomers. Blue fitted, red included
  • Tool-free CNC preload knob

Throttle

  • 10 kg load cell, bolted into the arm
  • VRS-engineered throttle spring, custom-manufactured for VRS, on a polished stainless centre rod
  • Ball-bearing swing bracket: the spring and shaft pivot with the pedal, so the spring never binds
  • Polished 304 stainless shaft in a low-friction POM bearing
  • Tool-free CNC preload knob with a wide range

Clutch

  • 80 kg load cell
  • Race car force curve: rises, then drops at the end
  • Clevis linkage with roller
  • Rear spring pivot held on both sides, on ball bearings
  • Tool-free CNC preload knob

All pedals

  • 3 mm laser-cut steel frame, deep black powder coat
  • Shielded ball bearings on the pivots
  • Dual end stops, 70 and 90 Shore, on hex spacers
  • 5 tilt positions, about 20°
  • Pedal face height (27 mm) and tilt adjustment
  • Faces curved to R400. Sport: 2 mm aluminium, CNC-machined edges, sandblasted, black anodised. Elite: CNC-machined from solid 6061, carbon grey anodised, diamond grip on brake and clutch

Electronics and software

  • VRS Pedal controller, all-aluminium, 3 pedal ports
  • 24-bit ADC, 14.3 effective bits
  • USB, 1.6 m cable
  • VRS One: calibration, maximum force, dead zones, firmware updates

Mounting

  • 4 × M6 per pedal, slotted, 70 × 120 mm pattern
  • Same footprint for throttle, brake and clutch
  • 87 mm wide per pedal, 92.5 mm with a damper
  • Optional G2 Baseplate

Compatibility

  • PC with a USB port, Windows 10 or above
  • Any game that supports controllers
  • The clutch uses the Pedal controller from the Throttle & Brake set
DirectForce Pro G2 Pedals

Measure the driver. Not the pedal.

A load cell on every pedal, a progressive mechanical brake, a zero-friction throttle and steel springs that feel the same on lap 100 as on lap 1. Throttle & Brake and Clutch, in Sport and Elite. Made in EU, with a three-year limited warranty.